• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet to go inside and out at their own pace, without needing to let them in or out. They also help stop your cat from urinating in the house.

It is much easier to put a cat flap on a Upvc panel than a glass one but you'll require some knowledge and appropriate tools.

Measure the Door

The installation of a cat flap in a front door could be difficult, but so long as the cat flap is the correct one and you follow the guidelines you can make it less difficult. We will help you draw the shape using a jigsaw in order to cut the door area. Then we will finish the job by attaching the flap. This will ensure the flap stays in position and shields the doors from damage caused by rain and wind.

The first thing you need to do is determine the width of your pet to get a precise measurement of the size of cat flap fitting near me flap you will require. This will ensure that the flap is big enough that your pet can leave and enter the home without needing to open and close the door every time, but it is also small enough to stop them from going too far in either direction.

If your kit has a drawing showing where to drill then you can place it on the door, and then draw around it. If your door has a sill or moulding at the bottom, be sure you leave enough space between your cat and these elements.

Set a square to check that you're cutting properly and to make sure the hole is in a rectangle shape. Once you are happy with the result, you can start removing the remaining door material. If you have a set square then use it to check that you are cutting correctly and to ensure that the hole is in a rectangular shape. Once you are satisfied with the shape, you can begin to take off the rest of the door material.

Draw a Line

The cat flap lets you to let your pet in and outside without having to worry about unwanted visitors or unwelcome gifts. It also prevents draughts, and helps to keep your home's temperature in check. However, putting a cat flap in your door might seem like an intimidating task for those who have never done it before, which is why many people to seek out a professional joiner or carpenter to complete the task. This is a viable option, however you can do it yourself if the tools are appropriate and the directions are followed.

This is much simpler to do with wooden doors, but it is still possible using uPVC. However it is important to be cautious not to scratch the doors because this will invalidate your guarantee. The first step in the process is to measure the door and ensure that it is able to accommodate the new cat flap. This should be simple enough if you are using the standard uPVC door, but you may need to take more care if you have an insulated or composite kind of door, as they are more difficult to cut into than solid uPVC panels.

The next step is to determine the height of your cat flap installers's stomach. This is the amount of height between the floor and the bottom of your cat's stomach. It is important to locate a space on the door that allows your cat to comfortably pass through. Once you know this then you need to mark out the area using an eraser and a spirit level to ensure that the hole you make will be suitable for your cat.

Once you've marked the area, you're now ready to cut the hole. You will need to use a jigsaw and it is essential to be patient to ensure that the cuts are clean and smooth, rather than uneven and rough, as it could cause damage to your door. Wear safety glasses and a dust mask when using a jigsaw. Inhaling sawdust can be harmful for your health. Once you've finished cutting the hole, you'll require sandpaper for smoothing the edges so that the cat flap can be easily inserted into the hole.

Cut a Hole

Getting a cat flap fitted into an existing door panel or double glazing sealed unit is quite difficult. If you are not very skilled in DIY, it is recommended to hire a professional to complete the job for you. A mistake in the process may not only be unsightly but also an enigma for security as well as allowing cold air to enter when the cat is outside and hot air to escape inside.

The first thing you need to do is draw the position of the hole in the door with an eraser and an ax level. This will ensure that it is located and is parallel to the other components of the door. You should make sure you have an sandpaper piece on ready to smooth out any rough edges.

Wear any safety equipment you need to work with the power tool. If you're worried about noise, you can buy a cordless jigsaw which is quieter and easier.

It is important that you only cut away the material required to fit the cat flap. A little bit of extra material is required to increase the thickness of the wall of the flap, but cutting off more than this can cause problems or cause damage to the door frame.

If the door is made of upvc and is made of metal, or has a frame, it may interfere with the microchip flap. In this situation you'll need create an over-sized hole to ensure that the metal does not get in contact with the wall of the flap.

If you want to install a cat flap inside a upvc or double-glazed window with frames made of metal you'll need to talk to a specialist. They can provide you with a new piece of glass that has the hole already made for the cat flap. This will be cheaper than fitting a cat flap in an existing pane of glass that was not designed for this purpose.

Install the Flap

Cat flaps let your pet come and go as they please, giving them the freedom to relax in the home whenever they want to. However, if you own an uPVC door, it might be difficult to fit a cat flap, especially in the absence of glass panes that could be cut to accommodate one. If you're able to buy and install a new half-glazed uPVC panel then it is possible to fit an animal flap onto the doors. It's not as easy as just making a hole in the door though and there are a few things you'll need to do first to ensure that it's secure.

A uPVC, GRP or composite door panel typically comprises an flimsy plastic outer layer that is bonded to a soft, polystyrene insulating core. The material is quite fragile and care must be taken when cutting through it to avoid causing damage. This kind door has a template you can use to make the hole.

After you've marked the location of the hole in your door, it's time to install the flap. You can pick from a range of models, ranging from simple push-button models to microchip-activated ones that only let your pet in. Whatever type of cat flaps you select it's essential that your cat can use the flap comfortably without getting stuck in the rain.

A circular fitting cat flap in Upvc door panel is better than a square one, as circles can be cut more securely into glass. This is because square holes are more likely to break the glass when they're drilled. It's also a how much to install a cat flap safer choice to use since you don't risk drilling into toughened glass that may break and hurt your pet or your family. This is particularly important if there are elderly or children living in your home that could be hurt by glass shards.