• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can fix hinges that are loose. If, however, the screw holes are damaged and won't hold screws you might have to use wood glue and dowels before you can install the hinge.

Clean up any surface rust. This will help keep the dowels in place and provide a solid foundation for them to grip onto.

Removal of the Hinges

Many hinges for doors can be removed, which makes it easier to move doors from one side of the frame to the other side or remove the entire door in the event of need. It is simple for anyone with a bit of patience, but you need to know how do it properly.

If the hinges have been painted, you'll need to remove it prior to trying to remove the pins. If you do not, the paint may peel off and scratch your door when you try to lift it. Put the hinges in an stainless steel pot and fill it with water until the hinges are submerged. Let the hinges sit in the pan for 30 minutes. The heat from the water should soften the paint and make it easier to remove the pins.

Once the pins are loosened, remove the hinges and the frame from the door. It is possible to use a standard screwdriver, however a magnetic screwdriver is recommended for this job. This type of screwdriver was designed to grab screws made of steel and will make the project speed up.

Before you attempt to remove the hinges, it is recommended to spray them with oil. A simple lubricant can help you to speed up the process and make the removal of screws and pins easier. You can purchase this kind of lubricant at most hardware and home improvement stores.

It is important to keep in mind that the number of hinges you'll need will vary depending on the kind of door and its settings. Heavy doors and solid-core doors will require more hinges while hollow-core doors that weigh less may only require two or three.

It is also important to understand the different types of hinges to decide which one will be the most effective for your particular situation. Exterior hinges are designed to support the weight of a door, while hinges for interior use must be able to support heavier loads.

Reattaching the Hinges

Over time, the hinges of doors may lose its grip and then begin to hang crooked or sag. It can be a big issue, but the solution is usually easy. In most cases an easy tightening of the screw will fix the issue. However in the event that the screw holes have been stripped out, this can be more difficult. There is a method to make these holes back to their original size that uses a wood dowel.

Begin by drilling the hole using a drill close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length exactly the same as the screw to ensure a snug fit. Then, reinstall the screw and tighten it to the desired level of tightness. If the door does not stop bind up, insert a second dowel into the gap. Repeat the process. Be sure to close the door slowly in order to examine the clearances around the perimeter after each adjustment.

You can also use a wooden plug instead of the dowel. This is also a viable option however it may take some time to put in. Simply whittle a plug of wood that is the appropriate size for a comfortable fit, then tap it into the hole. If you don't have a woodworking tool, you can also try using toothpicks or wooden matches.

Make use of a countersink in order to make the hole smaller than the head of screw after you have reinstalled it. This will prevent the screw from rubbing against the edge of the doors as they are closed and opened. This will make it easier to tighten the screw when reinstalling the hinge.

After you have reinstalled the window hinge broken, be sure to coat it with a dry lubricant in order to prevent it from getting stuck in the future. You can use products like PB Blaster and Liquid Wrench. You should apply a light coat and give it approximately 15 minutes to get into the hinge barrel.

Refinishing the Hinges

If you're unsure whether to replace your hinges, you can try a few simple fixes. Verify that the screws that hold the hinge plate in place to the door frame and frame are in good condition. If they're loose, tighten them using the help of a screwdriver or a power drill. Be careful not to tighten the screws so tight that they begin to create gaps in the trim joints, or even worse cause threads to be stripped.

If the issue is that the hinge plates are breaking away from the door and jamb, you can reattach them by applying wood glue to the back of the plates and then inserting toothpicks or wooden dowels into the holes. The dowels or toothpicks provide a solid base for the screws and to prevent the plates from shifting when you drive them into position. Let the glue dry before attaching the hinge.

Another reason for loose hinges is that the screws are stripped or gone. This can be corrected by replacing the screws. Make sure the drill bit is exactly the same size as the screw hole to avoid drilling into the jamb or hinge.

Once you've reattached the hinge, close the door and examine the gap between the frame and the door. It should be about the thickness of one nickel all around or less if there's an existing gap that was caused by a previous door that was not properly hang. If the hinges were put in place properly, this shouldn't be a problem.

If you find that the hinges remain loose, try adding a thicker hinge shim between the hinge plate and the mounting surface to add a little extra space. You could also try taking the hinge pin from the problematic hinge and pounding it down with a hammer to make it tighter or using a new hinge pin altogether. You can also lubricate your hinges with mineral or Jojoba oil to lessen friction and help them hold their position. Lubricating your hinges regularly can keep them from becoming stiff tilt and turn hinges for upvc windows squeaky, and also extend their lifespan.

Cleaning the Hinges

The friction created by a hinge's constant movement draws dust particles. These particles can become stuck and build up in the moving parts of door hinges if they're not maintained and cleaned regularly. In the end the hinge can become stiff and creaky and its appearance may deteriorate rapidly. Regular cleaning, lubrication and inspection will preserve the integrity and functionality of hinges on a door.

Inspect the hinges to see how much rust has formed on their surface. If the rust has corroded to the point of destroying the surface of the hinge barrel or screw holes, you'll need to replace the hinges. If you are able to save the hinges, first brush away loose rust using steel wool and a wire brush. Then, apply a commercial rust remover or homemade solution like lemon juice to the hinge. Allow the rust-removing solution to sit on the replacement upvc window hinges for a few minutes to penetrate and dissolve the remaining rust.

The tightening of screws can restore broken window hinge repair function in the event that you don't want to spend time or money on repairing hinges. If you've stripped the screw holes, however, it may be necessary to add an wooden dowel or shim to the hinge. Dowels made of wood are square pieces made of wood in the shape of rods which are available in various lengths and diameters. You can buy them on the internet, at woodworking supply shops and home improvement stores.

You can also make an shim using made of plastic or metal depending on the type hinge you have. To make a dowel, cut a piece made of wooden dowel or another sturdy material to the size you want. You can then dip a dowel into carpenter's adhesive and insert it in the hole. The glue will hold the dowel securely in place.

Before cleaning the hinges, put down a cloth or towel to shield your flooring from spills. Once the area is protected and dry, clean the hinges using an absorbent sponge or a soft cloth that has been soaked in mild cleaner or vinegar to remove built-up dirt, grime and tarnish. You can use a toothbrush or small brush to get into difficult-to-reach areas in crevices and tight areas.