• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work high above the ground, moving massive glass panes. They adhere to strict safety standards and are often working in harsh weather conditions.

While wearing protective clothing, remove all glazing putty and glazing points with a utility knife. A heat gun can to soften and eliminate the old putty.

Replacement

It's tempting to fix the glass of your window instead of replacing it if panes break. It is cheaper to replace windows and it will also help prevent other problems in the efficiency of your home. You should also take into consideration the type of glass that is broken to determine if this is temporary or if you'll need to invest in an option that is more permanent.

The first step in repairing damaged windows is to remove the sash, or frame and place it flat on a work table. Wearing eye protection, gently wiggle the window's pane and pull out any remaining fragments. Then, use a utility knife to remove the glazing compound and glazing points that help to hold the glass in place. Make sure you keep track of the components and their locations to ensure that they can be replaced later.

After removing the frame and sash you can begin to prepare to replace the glass. Be sure to check that the opening of the frame is of the correct size for your replacement window. Take measurements both ways across the opening, and then subtract 1/8 inch from each measurement to give room for expansion and contraction of the frame and glass. Then, buy double-strength glass cut to these exact measurements. It is a good idea to also purchase enough glazier's clips or points to install every 6 inches around the window pane.

If the manufacturer is accountable you should contact them and submit a claim. After the new glass has been erected it is essential to cover it with a thin layer glaziers compound. After the compound has dried and dry, you can paint it to match the rest of the frame.

If you have a crack that extends more than an inch, scoring a small arc with a razor blade just beyond the crack can help to stop it from spreading further. This trick is not foolproof but it can slow the progression of the cracked until you can take permanent measures.

Repair

Professional window installers are equipped with the right tools and know how to handle different kinds of glass. They are able to dispose of waste properly, so they are less likely than other people to leave behind scraps that could inflict harm on family pets or members of the family. They're also accustomed to working with various types of windows and may be aware of issues that aren't apparent to the uninitiated homeowner.

Wear safety glasses and gloves prior to beginning repair work on cracked glass. Even a small break can cause shards to fly off, creating a risk for anyone in or around the home. It's important to determine the cause of the crack, as this could prevent future problems.

Create a two-part mixture of epoxy. They typically are a 50/50 mixture of hardener and resin. They must be mixed quickly. After the mixture is prepared and applied, simply apply it to the crack and allow it to dry. It should take only about a few minutes, but you must be quick because the mixture is thick and drys very quickly.

Once the epoxy has dried, you can take off excess epoxy with a putty blade. Then, you'll have to clean the area around the cracked glass. If you don't clean the area properly the leftovers could cause further damage to the glass. After cleaning the glass using a putty knife, you can use it to smooth the compound along the edges of the window, and then match it with the frame of wood.

If you want a more durable solution, consider using a plastic cover. You can cover the glass using masking tape or a heavy-duty trash bag. This will prevent the crack from spreading, and will also keep water, wind and insects out.

If you're not able to get to the window repair fast enough and you're not able to get there quickly, you can use silicone sealant to make an interim repair. Simply place a tiny amount of the stuff around the outside edge of the broken pane. It won't completely seal the gap between the glass and the frame completely, but it will hold the break in place until you are able to fix it.

Repainting

If your glass windows are old, you might consider repainting them. This is a cost-effective alternative to replacing windows and it can give your home a new look. Before painting, make sure the surface is clean. Use soap or rubbing alcohol and water to wash away oil smudges, as well as other residues which can prevent paint from adhering. It is also recommended to wear rubber gloves when working on glass to prevent the transfer of your own oils onto the glass surface. Finally, you should apply several thin coats of paint instead of a single thick layer. This will make the paint last longer and make your windows appear smooth and even.

If you're planning to paint your glass windows, be sure you have the proper tools in your arsenal. You'll need a brush, sponge, painter's adhesive, a ruler, toothpicks, and a few other tools such as paper towels or a rag. You'll need the brushes and paints you'll be using on hand. Follow the manufacturer's directions. Have patience, as it may take some time for the paint to fully dry.

If you are using solvent-based paint, you should make sure that the area in which you work is well ventilated. This will reduce the chance of inhaling harmful chemicals, and the paint will dry more quickly. Wear a mask to protect yourself when using spray paints.

For older glass windows, you'll need to prepare the surface prior to painting. Clean the glass window thoroughly using soap and warm water, then use rubbing alcohol to clean off any oil or grease that could affect the paint's adhesion. Be sure that the windows are completely dried before you begin to paint them.

If your glass windows are energy-efficient dual pane windows, you might be eligible to submit a claim repairs to double glazed windows the window company or dealer that sold them to pay any repair or replacement costs. This is especially true if the windows are still under warranty and have experienced multiple problems with condensation or damaged glass.

Sealing

If you have double glazed window repairs-pane windows with cracked seal or newer insulated glass units (IGUs) that have experienced fogging, there are several methods to address the issue. The most costly option is to replace the insulated unit and frame but it may be required if fog or condensation cause energy loss. Other options include replacing the IGU by a single pane, or repairing the existing IGU by drilling a hole through the bottom and filling it up with an anti-fogging agent.

You can also seal the gap between the window frame and the threshold or sill with a felt strip, vinyl v-strip, or a door sweep. Felt can be stapled, glued or placed in place, but does not offer much protection against moisture. Vinyl v-strip is easy to install and long-lasting however it can be expensive. It is usually reserved for areas that are exposed to abrasions that are high. upvc door repair sweeps are affordable and can be fixed into place however they provide little to no barrier between the sill or threshold and air, dust, and other debris.

To repair a damaged window seal make use of a putty blade to take off the caulk. Wearing eye protection and gloves remove the glazing point -- tiny fasteners with sharp pointed tips that hold the glass in the recess of the frame. Once you have removed the glazing points, scrub the grooves and sand the wood until it is smooth. Wipe off any sanding debris and then seal the unfinished wood surface using a linseed oil-based paint or clear sealer.

A caulking knife or putty can be used to apply traditional glazing putty, however a knife will provide a more precise application, and a better seal. Select a putty made specifically for glass as it will last longer and stick better.

Apply a small amount of the putty to the inside edge of the frame where it touches the glass. Slide the window into the frame so that the scribed line on glass lines up with the frame's edge. Apply pressure on the glass to press the putty and glass to form a tight seal. Smooth the compound with fingers that are gloved and clean up any caulk that is applied incorrectly or spills that are not properly wiped away prior to drying.