• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat key cutting 500 Key Fob Won't Work

A key fob for the fiat 500 spare key 500 makes it simple to open doors and start your car. There are a myriad of reasons why the key fob might stop functioning. These include a dead coin battery or damage to the receiver module, water problems, and interference.

This listing is for an NEW replacement fiat key cutting Flip Key Remote - an exact replica of the Ilco brand that must be professionally programmed by a local locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob will not work is the battery is dead. Modern key fobs offer limited operating range and must be within a few inches of your vehicle to work. If you are far from your vehicle when you press the key fob button, the car won't respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery of your coin cell (Part number CR2032) by a new one from a trusted brand like Panasonic, Duracell, or Energizer. They are usually available at your local hardware store, or online.

After you've changed the battery on the coin cell You can test it by standing near your fiat ducato key programming 500 and pressing the buttons. The car should blink its parking lights and the key fob should operate the lock and unlock switches.

If the fob's remote doesn't function after replacing the battery, it may have water damage that stops it from communicating with the receiver module in your car. Water damage can occur in many ways, such as simply splashing or submerging the key fob saltwater at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If that doesn't work, your fob will probably need to be reprogrammed by an experienced locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob in the ocean or wash it in a machine. Saltwater can cause the circuit board to short and eventually end up dying. It's not a good thing to get the fob wet but don't give up if you accidentally drop it in water or forget to take it out of your pants pocket.

First take the battery off the fob. Before replacing the battery, clean the electronic chip using isopropyl or another similar product. Check the fob to determine if it's functioning. If the key does not work, it may have to be reprogrammed. This is usually handled by a dealer or professional auto locksmith.

If the key is more recent and hasn't been programmed to your vehicle, it will likely need to be replaced completely. A professional locksmith in the automotive industry can carry out this simple task. The locksmith will require the key to be cut to match the car's ignition. They will also need to reprogram the fob in the system of your car. This is a simple and cost-effective process that can usually be completed on the same day.

Receiver Module Issues

The 500 key fob could be inoperable because it's out of range. The remote has a range of 30 feet, which means when you're too far away from your vehicle, it won't respond to your commands. It is possible to remedy this by moving your remote closer to your vehicle until it responds.

If your fob isn't working after replacing the battery in the coin, also known as a "button", "watch" or "button" it may be due to a malfunction on the circuit board inside. Reprogramming the fob usually resolves the issue. You can find the instructions on how to do this for the majority of vehicles by searching YouTube or consulting the owner's manual.

It's possible that you need to replace the metal retaining clips that keep the coin battery. If they lose tension, it can stop your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob might become disconnected from your vehicle due to software issues or hardware issues. This can cause a major problem, but you can often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain situations they may have to reinstall the program in your body control module, as well.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This may happen if the keyfob is located in close proximity to a radio transmitter, like a cell phone or radar detector. Other reasons why the key fob could not function may be a lack of connection to the buttons or the internal chip, or water damage.

If the key fob suddenly stopped working, without notice or after trying every option at home to resolve it e.g. You could have a malfunctioning 500 receiver module If you've tried replacing it with a battery, reprogramming, or using a spare key fob. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It transforms the signals into electronic commands, which are then translated by the vehicle.

Luckily, there is an easy method to reset all of the on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then reconnect the battery. This will clear out any remaining electricity and then restart the car's computers. This can help you the key fob to function again. If the issue continues you should speak with a certified technician. They will be able to determine the root of your problems.